1-канальный усилитель класса D, 300 Вт х 1 @ 2 Ом / 160 Вт х 1 @ 4 Ом, 14.4 В

SKU 98400 | Model HX 300/1
купить в магазине

Представитель особо компактных усилителей нового поколения, этот моноблок отлично приспособлен для установки не только в автомобили, но также на мотоциклы, квадроциклы и другую технику для активного отдыха. Узкий вытянутый корпус с устойчивым к коррозии порошковым покрытием готов к суровым условиям эксплуатации, со степенью защиты от влаги IPX6. Также предприняты меры для защиты от грязи, а прикрывающая панель управления защитная крышка имеет надежный резиновый уплотнитель. Комплектные крепежные аксессуары выполнены из нержавеющей стали.

Впечатляющая мощность 300 Вт (2 Ом, 14.4 В, 1% THD), наличие плавно настраиваемых фильтров НЧ и ФИНЧ (subsonic), схемы подъема баса и инвертора фазы приносят отличные результаты при работе с сабвуфером. Вместе с тем, расширенный до 12 кГц диапазон частот позволяет использовать усилитель с динамиками других регистров (кроме ВЧ-динамиков) в мощных системах развитой конфигурации. Возможно подключение к источнику сигнала как с низкоуровневыми, так и с высокоуровневыми аудиовыходами. Усилитель работает в энергоэффективном классе D, где применение патентованной технологии NexD™ привело к существенному росту качества звучания. В басовом регистре выгодно подчеркивается не только мощность и глубина баса, но также быстрая атака с хорошо выраженным "панчем" и четкий контроль звучания. При желании можно приобрести за дополнительную плату пульт ДУ M-RBC-1 для оперативной регулировки уровня громкости сабвуферного канала с водительского места.

Частотный диапазон
20 Hz - 12 kHz (+0, -1dB)
Отношение сигнал/шум измеренное на максимальной мощности
>85 dB below rated power (A-weighted, 20 Hz - 20 kHz noise bandwidth)
Отношение сигнал/шум (1 Вт)
>64 dB (A-weighted, 20 Hz - 20 kHz noise bandwidth)
Демпинг фактор @ 4 Ома
>150 / 50 Hz
Демпинг фактор @ 2 Ома
>75 / 50 Hz
Коэффициент гармонических искажений
<1% @ 2 Ω
Чувствительность входов @ RCA
Switchable from 250 mV - 4 V RMS (Low) to 750 mV - 15 V RMS (High)
Рекомендованное сечение кабеля питания с проводниками из 100% меди
8 AWG wire
Номинал предохранителя
30 A (AFS, AGU or MaxiFuse™)
Высота (H)
1.77 in / 45 mm
Ширина (W)
8.66 in / 220 mm
Глубина (D)
3.09 in / 78.5 mm
@ 4 Ома
160 W RMS x 1
@ 3 Ома
200 W RMS x 1
@ 2 Ома
250 W RMS x 1
@ 1.5 Ома
N/A
@ 4 Ома
160 W RMS x 1
@ 3 Ома
200 W RMS x 1
@ 2 Ома
250 W RMS x 1
@ 1.5 Ома
N/A
Вес
3.18 lb / 1.44 kg
Типы фильтров
Low-Pass only
Крутизна фильтра
24 dB/octave
Диапазон регулировки фильтров
40 Hz - 400 Hz
Возможность пошаговой настройки частоты среза
Yes
Возможность отключения фильтра
Yes
Сабсоник фильтр
20 Hz - 40 Hz, variable
Басс буст
0 to +12 dB @ 43 Hz
Переключатель полярности
Yes
Проводной пульт регулировки уровня сабвуфера
Optional (M-RBC-1)
Дистанционная регулировка басс буст
No
Линейный выход
None

NexD™ Switching Technology

NexD™ Switching Technology

Summary:
NexD™ amplifier technologies produce exceptional audio quality, unsurpassed total efficiency and high power from very compact amplifier designs.

Detailed Information:
Beginning with the original 'Slash' subwoofer amplifiers, JL Audio has been at the forefront of Class D amplifier design. Today, our flagship Single-Cycle Control™ technology sets the ultimate standard for Class D amplifier performance. The NexD™ amplifiers may be a bit less complex, more compact and more affordable, but they flow from the same minds that have set the trend in mobile amplifier technology for over a decade.

Let's get a little nerdy... A traditional PWM switching amp design uses a fixed switching frequency and varies the pulse width based solely on the audio input signal to the pulse modulator. This basic approach assumes some ideal conditions, like a rock-steady power supply, that do not necessarily occur in a real, in-car installation. Power supply sag with signal causes distortion at all power levels with these designs, even well below clipping. The cure for this is feedback (a corrective signal sent back to the input side), but this becomes impractical as the audio frequency increases, making it a good solution for band-limited (subwoofer) amps, but not for full-range amplifiers.

Taking the above into account when designing the NexD™ subwoofer amplifiers, we have taken the simple fixed PWM approach and enhanced it with a very high switching frequency: 240 kHz, which is about 4x higher than most Class D subwoofer amplifiers. This pushes the amplifier's bandwidth to at least 500 Hz with minimal distortion and improves efficiency, while keeping typically bulky circuity more compact. Your subwoofers will reward you with tight, rock-solid bass performance.

For the full-range NexD™ amplifiers and channels we applied a variable, ultra-high speed version of the NexD™ technology (switching at well over 400 kHz). In these designs, a self-oscillating modulator with "feed-forward" sends information about the instantaneous power supply voltage to the modulator, combining this with the input signal to cancel out any distortion due to supply voltage fluctuation. This reduces distortion prior to applying feedback, simplifying the overall feedback loop design.

The bottom line is simply great audio: clean, powerful and reliable.

 

 

Differential-Balanced Inputs

Differential-Balanced Inputs

Summary:
JL Audio’s Differential-Balanced Inputs are engineered to combat induced cable noise, which is a common problem in car and marine audio installations. This technology allows for the use of conventional RCA cables, while delivering many of the benefits of a true balanced connection and accepting a wide range of input signal levels.

Detailed Information:
Today’s vehicles are equipped with sophisticated electronics capable of generating noise and interference that can intrude into the audio path, ruining the listening experience.

Most audio equipment uses single-ended, ground-referenced RCA jacks to receive audio signals. This means that the RCA shield is connected directly to signal ground. This is a simple, cost effective input design that works well for short runs in noise free environments. In noisier environments, this method cannot reject the common mode noise that could be on both RCA conductors (shield and center conductor).

By having more than one chassis-grounded RCA shield on a device, single-ended input designs are also more susceptible to ground loops. If noise is present on both conductors while the shield is connected to ground, the input amplifier will amplify the noise relative to the grounded RCA shield. When there are multiple RCA connections or any other conductors subjected to a magnetic field, this will cause a difference in potential across the RCA loop to be amplified at the grounded RCA as noise (a classic ground loop).

JL Audio’s Differential-Balanced Input circuits measure the center pin of the RCA connection relative to the RCA shield, even when the shield is not connected to ground, and even when the voltages at both conductors are moving relative to ground. Because both the center conductor and the shield see high impedance to ground at the input, a ground loop cannot be formed, as there is no current flow to induce a voltage as noise. This works equally well with differential-balanced, or unbalanced signal sources, making this input architecture compatible with all standard car and marine audio equipment, using standard, unshielded, twisted-pair RCA cables. No special cables are required, unlike the fully balanced connections used in professional audio.

Another benefit of the Differential-Balanced Input design is that it easily accepts low-level and high-level signals from a variety of factory head unit outputs and amplifiers, including single ended “ground referenced” sources, as well as Balanced or Unbalanced “Bridged or BTL” sources. This eliminates the need for Line Output Converters (LOCs) in most installation scenarios.

The obvious question is: “Why don’t all car audio amplifiers use Differential-Balanced Inputs?” The answer is simple: it costs more. Executing a proper differential-balanced input section requires more components and better quality components than a basic single-ended design, so you generally won’t find them on less expensive amplifiers.